Are you looking for information about garage floor epoxy? Here you will find information about it.
Coating your garage floor with the right epoxy is a great idea. It will look really fantastic if you apply this to your garage floor. You will surely love it. What you need is an epoxy shield garage floor coating, a two part water based epoxy coating system that provides superior protection and durability in just one coat. Epoxy shield is a high performance, easy to apply garage floor coating. Preparation is key to a lasting finish. So, it’s important that you follow all preparation and application instructions carefully. Be aware that not all surfaces are suitable for painting. Check your surface for sealant, poorly bonded previous paint, moisture in the concrete, loose or poorly cured concrete or concrete dust. If you suspect your floor has any of these conditions, test the surfaces as directed in the epoxy shield garage floor instruction sheet. Apply the coating when the air temperature is 60 to 85 degrees Fahrenheit and when the floor is a minimum of 55 degrees Fahrenheit.
Preparation
1. Use epoxy shield heavy duty degreaser or a solvent like mineral spirits. Use a scrub brush to remove any oil or grease spots on the floor.
2. Scrub the spots thoroughly and absorb excess cleaner with rags or any equivalent.
3. Rinse completely to remove all cleaner and contaminants.
4. Repair damaged areas with epoxy shield concrete patch and repair. Allow it to fully cure before proceeding.
5. Next, prepare the entire surface using the concentrated cleaner included in the kit.
6. Mix the concentrated cleaner with two gallons of water until all cleaner is dissolved.
7. Use plastic water in can to help you evenly distribute the solution.
Apply Cleaner
8. Pre-wet the whole floor using the hose. Then, spread the cleaner solution over the surface in 10 ft. by 10 ft. sections.
9. Work the solution into the concrete using a bristle brush.
Rinse Thoroughly
10. As each section is completed, rinse thoroughly with water continuing to scrub with the brush to help move dirt and contaminants out of the garage.
Video from YouTube.com
Note: Here’s a tip. Use an inexpensive foam squeegee to most effectively move dirt and water out and speed drying time.
11. Rinse and squeegee twice before moving on to the next section.
12. Once all sections are completed, rinse and squeegee the entire floor to remove any cleaner that may have been trapped on previously cleaned areas. A wet-dry vacuum can also be used to eliminate excess water, dirt, and contaminants.
13. Allow the entire surface to dry completely.
14. Wipe your fingers over the clean, dry floor. If you see any dust or powder on your finger, repeat the rinsing and scrubbing until the floor is clean.
Activate
15. Next, activate the epoxy shield system by pouring all of Part A in the Part B.
16. Stir thoroughly with the mixing stick for at least 3 minutes.
Check the Temperature Charts
17. After stirring, check the temperature charts in the epoxy shield garage floor instruction sheet for the appropriate application time. This allows the epoxy shield to fully activate.
Do Not Leave in Direct Sunlight
18. Once mixed, the product must be used within the time indicated in the charts. Do not leave the mixed product in direct sunlight.
19. Stir the mixture one more time before applying.
20. To create a slip resistance surface, add epoxy shield anti-skid additive to the mixed coating.
21. If using more than one kit, do not mix kits at the same time. To ensure even gloss and color, the coating must be applied within the time stated in the charts.
22. Then, use a roller to apply the coating in 4 ft. by 4 ft. sections.
Add Chips
23. Once the section is completed, sprinkler the decorative chips over the wet film.
24. Continue in this manner until the entire floor is complete.
Epoxy shield is a low odor environmentally friendly coating and clean up is easy. Just use soap and water to clean your hands and tools. The surface should be ready for light foot traffic in about 12 to 16 hours. Wait for 24 to 48 hours before placing heavy items in the floor. Allow the floor to cure for 7 days before parking vehicle in the surface.
Based from the above procedure, it is so simple to apply. It’s as easy as painting the wall.
Home|About|Contact|Privacy|Sitemap